扭剪扳手检验及保养
Inspection and maintenance of torsional shear wrench
1、必威西汉姆联官网g1线路的金属外壳应可靠接地，其外壳应有定期检验试验合格证，并在期限内。
1. The metal shell of the electric wrench shall be reliably grounded, and its shell shall be provided with regular inspection and test certificate within the time limit.
2、检查必威西汉姆联官网g1线路机身安装螺钉紧固情况，若发现螺钉松了，应立即重新扭紧，否则会导致必威西汉姆联官网g1线路故障。
2. Check the fastening of the mounting screws on the body of the electric wrench. If the screws are found to be loose, tighten them again immediately, otherwise the electric wrench will fail.
3、检查手持必威西汉姆联官网g1线路两侧手柄完好，不开裂可破损，安装牢固。
3. Check that the handles on both sides of the hand-held electric wrench are intact, not cracked or damaged, and installed firmly.
1、确认现场所接电源与必威西汉姆联官网g1线路铭牌是否相符。是否接有漏电保护器。
1. Confirm whether the on-site power supply is consistent with the nameplate of the electric wrench. Whether leakage protector is connected.
2、根据螺帽大小选择匹配的套筒，并妥善安装。
2. Select the matching sleeve according to the size of the nut and install it properly.
3、在送电前确认必威西汉姆联官网g1线路上开关断开状态，否则插头插入电源插座时必威西汉姆联官网g1线路将出其不意地立刻转动，从而可能招致人员伤害危险。
3. Before power transmission, confirm that the switch on the electric wrench is disconnected, otherwise when the plug is inserted into the power socket, the electric wrench will turn unexpectedly immediately, which may cause personal injury.
4、若作业场所在远离电源的地点，需延伸线缆时，应使用容量足够，安装合格的延伸线缆。延伸线缆如通过人行过道应高架或做好防止线缆被碾压损坏的措施。
4. If the workplace is far away from the power supply and it is necessary to extend the cable, use the extension cable with sufficient capacity and install the qualified extension cable. If the extension cable passes through the pedestrian aisle, it shall be elevated or measures shall be taken to prevent the cable from being crushed and damaged.
5、尽可能在使用时找好反向力距支靠点，以防反作用力伤人。
5. Try to find the supporting point of the reverse force distance during use to prevent the reaction force from hurting people.
6、使用时发现电动机碳火花异常时，应立即停止工作，进行检查处理，排除故障。此外碳刷一定要保持清洁干净。
6. In case of abnormal carbon spark of the motor during use, stop working immediately, check and deal with it and eliminate the fault. In addition, the carbon brush must be kept clean.
7、站在梯子上工作或高处作业应做好高处坠落措施，梯子应有地面人员扶持。
7. Measures for falling from height shall be taken when working on a ladder or working at heights, and the ladder shall be supported by ground personnel.
以上就是为大家介绍的有关
扭剪扳手价格的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务
The above is about the price of torsional shear wrench I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service
