我们济南万中供应的可扭剪的必威西汉姆联官网g1线路只需要更换内外套筒即可适用于各厂家生产的M16-M30扭剪型螺栓的施工作业，本机采用特殊钢材及特殊的热处理工艺，经久耐用，作业时无反弹力。可扭剪的必威西汉姆联官网g1线路主要是终紧扭剪型螺栓的，它的目的就是把扭剪型螺栓的梅花头打断即可。工作时将扳手头对准螺栓头，扣动开关即可开始工作，几秒后，螺栓梅花头将被扭断，然后抽出扳手扣动扳机将梅花头弹出，即结束工作。
The torsion shear electric wrench supplied by Jinan Wanzhong only needs to replace the inner and outer sleeves. It is suitable for the construction of m16-m30 torsion shear bolts produced by various manufacturers. The machine adopts special steel and special heat treatment process, which is durable and has no rebound force during operation. The electric wrench with torsion shear is mainly used to finally tighten the torsion shear bolt. Its purpose is to break the plum blossom head of the torsion shear bolt. When working, align the wrench head with the bolt head, pull the switch to start working. After a few seconds, the bolt plum blossom head will be broken, then pull out the wrench and pull the trigger to pop up the plum blossom head, that is, end the work.
扭力的单位及换算:1N（牛）≈0.1KG（公斤) 1KG（公斤）=9.8N（牛） 1NM（牛米）≈0.1KGM(公斤力) 1KN（千牛）=0.102t（吨）=102KG（公斤）
Torque unit and conversion: 1n (n) ≈ 0.1kg (kg) 1kg (kg) = 9.8N (n) 1nm (nm) ≈ 0.1kgm (kg force) 1kn (KN) = 0.102t (T) = 102kg (kg)
选购扭力扳手技巧与常识：
Skills and common sense of purchasing torque wrench:
如果您是要装配及安装用的扭力扳手就可以用我司的预置式扭力扳手和电动扭力扳手
If you are a torque wrench for assembly and installation, you can use our preset torque wrench and electric torque wrench
如果您是要螺栓紧固检测及控制就可以用我司的数显扭力扳手及表盘扭力扳手
If you want bolt tightening detection and control, you can use our digital display torque wrench and dial torque wrench
如果您是要检定各种扭力扳手及扭力起子就可以用我司的扭力扳手校准仪
If you want to verify all kinds of torque wrenches and torque drivers, you can use our torque wrench calibrator
如果您是需要拆装强扭力的螺栓就可以用我司的扭矩倍增器
If you need to disassemble bolts with strong torque, you can use our torque multiplier
可扭剪的必威西汉姆联官网g1线路功能特点：
Functional features of electric wrench with torsion shear:
1.高速马达、低噪音、大功率、额定电压220V50/60Hz；
1. High speed motor, low noise, high power, rated voltage 220V50 / 60Hz;
2.优质,缘工程材料机壳、双重,缘、安全坚固可靠；
2. High quality, edge engineering materials, casing, double edge, safe, solid and reliable;
3.枪式握把、负荷人体工学、增加握持力、减轻疲劳强度；
3. Gun grip, load ergonomics, increase grip force and reduce fatigue strength;
5.行星减速、功效提高、运行平稳；
5. Planetary deceleration, improved efficiency and stable operation;
可扭剪的必威西汉姆联官网g1线路螺栓的拧紧操作
Tightening operation of electric wrench bolt with torsion shear
1、装上反力支架，并紧固螺钉。开动主机，使方头销孔与反力支架孔相对应，然后装入扳手套筒，插上销钉，并用橡胶圈固定。
1. Install the reaction support and tighten the screws. Start the host so that the square head pin hole corresponds to the reaction support hole, then install the wrench socket, insert the pin and fix it with a rubber ring.
2、将控制仪的扭矩旋钮调到所需扭矩值，将主机正反开关拨到正转位置，把扳手套筒套在螺纹连接件的六方上。
2. Adjust the torque knob of the controller to the required torque value, turn the forward and reverse switch of the host to the forward position, and put the wrench socket on the hexagon of the threaded connector.
3、按下电源开关，扳手启动。当反力支架力臂靠牢支架时（支点可以是邻近的一只螺栓或其他可作支点的位置）螺栓开始拧紧。当螺栓扭矩达到预定扭矩时，扳手自动停止，紧固完成，松开电源开关，进行下一只螺栓的拧紧工作。
3. Press the power switch and start the wrench. When the force arm of the reaction support is firmly against the support (the fulcrum can be an adjacent bolt or other position that can be used as the fulcrum), the bolt begins to tighten. When the bolt torque reaches the predetermined torque, the wrench automatically stops, the tightening is completed, the power switch is loosened and the next bolt is tightened.
4、扳手自动停止后，靠反力支架的弹性形变力，使支架力臂自动脱离支点，取下扳手。如力臂不能脱离支点时，可拨动正反开关，点动电源开关扳手即可取下。
4. After the wrench stops automatically, the force arm of the support will be automatically separated from the fulcrum by the elastic deformation force of the reaction support, and the wrench can be removed. If the force arm cannot be separated from the fulcrum, the positive and negative switch can be turned, and the power switch wrench can be removed by inching.
可扭剪的必威西汉姆联官网g1线路的选择与调节
Selection and adjustment of electric wrench with torsion shear
1、用户可在50-5500Nm的范围内任意选择相应规格的大量程扭剪型电动扭矩扳手。
1. The user can arbitrarily select a large range torsion shear electric torque wrench of corresponding specifications in the range of 50-5500nm.
2、控制仪面板上有“扭矩调解旋钮”。刻有0-10个刻度值。细调旋钮的作用是在粗调两档之间进行调节补偿，以提高扭矩控制精度。
2. There is a "torque adjustment knob" on the panel of the control instrument. It is engraved with 0-10 scale values. The function of the fine adjustment knob is to adjust and compensate between the coarse adjustment and two gears, so as to improve the torque control accuracy.
