扭剪扳手使用和操作注意事项
Cautions for Use and Operation of Torsion Spanner
1、确认现场所接电源与必威西汉姆联官网g1线路铭牌是否相符。电动扭剪扳手是否接有漏电保护器。
1. Verify that the power supply connected to the scene is consistent with the nameplate of the electric wrench. Whether the electric torsion shear wrench is connected with leakage protector.
2、根据螺帽大小选择匹配的套筒，并妥善安装。
2. Select the matching sleeve according to the size of the nut and install it properly.
3、在送电前确认必威西汉姆联官网g1线路上开关断开状态，否则插头插入电源插座时必威西汉姆联官网g1线路将出其不意地立刻转动，从而可能招致人员伤害危险。
3. Make sure that the switch on the electric wrench is off before power transmission. Otherwise, when the plug is inserted into the power socket, the electric wrench will turn unexpectedly and immediately, which may lead to the danger of personal injury.
4、若作业场所在远离电源的地点，需延伸线缆时，应使用容量足够，安装合格的延伸线缆。延伸线缆如通过人行过道应高架或做好防止线缆被碾压损坏的措施。
4. If the work place is far away from the power supply, when it needs to extend the cable, it should use enough capacity to install qualified extension cable. Extended cables should be elevated if they pass through pedestrian walkways or measures should be taken to prevent them from being damaged by rolling.
5、尽可能在使用时找好反向力距支靠点，以防反作用力伤人。
5. Find the supporting point of the reverse force distance as far as possible in order to prevent the reaction force from hurting people.
6、使用时发现电动机碳火花异常时，应立即停止工作，进行检查处理，排除故障。此外碳刷必须保持清洁干净。
6. When abnormal carbon spark of motor is found in use, it should stop working immediately, check and deal with it, and troubleshoot it. In addition, carbon brushes must be kept clean and clean.
7、站在梯子上工作或高处作业应做好高处坠落措施，梯子应有地面人员扶持。
7. When working on a ladder or at a high place, measures for falling from a high place should be taken, and the ladder should be supported by ground personnel.
扭剪扳手的功能特色
Functional features of twist-shear wrench
扭力扳手的分类：现在市面上的扭力扳手主要分三类，数显扭力扳手、表盘扭力扳手和预置式扭力扳手。
Classification of torsion wrenches: There are three main types of torsion wrenches on the market, digital display wrenches, dial wrenches and preset wrenches.
功能特色：
Functional features:
1.数位扭力读取值
1. Digital Torsion Readout Value
2.可切换多种接头，可根据不同的工作要求更换
2. Various connectors can be switched and replaced according to different working requirements.
3.CW顺时针：±3%，CCW反时针：±4%
3.CW clockwise: +3%, CCW counterclockwise: +4%
4.顺时针及逆时针皆可操作
4. Clockwise and counterclockwise operation
5.峰值保持及追随模式
5. Peak Holding and Following Patterns
6.蜂鸣器及LED指示（达到预订扭力值时）
6. Buzzer and LED Indicators (Upon reaching the predetermined Torsion Value)
7.四种种工程单位互转（N-m、ft-lb、in-lb、kgf-cm）
7. Four types of engineering units (N-m, ft-lb, in-lb, kgf-cm)
8.多笔可储存记录值。不必反复设置扭矩。
8. Multiple records can be stored. There is no need to set the torque repeatedly.
9.通讯功能
9. Communication function
10.可使用充电电池
10. Use rechargeable batteries
